Pages: 276
File size: 2.40MB
License: Free PDF
Added: Dour
Downloads: 93.800

However, you can also use the spanning-tree protocol-migration mwnagement at any time to manually re-check the appropriate BPDU format to send on the selected interfaces i. Microsoft gigabit ethernet stackable layer 3 switch managment guide pages. Keywords identify a command, and arguments specify configuration parameters. Use the no form to disable this function. Default Setting None Command Mode Page 57 Shows all routing entries, including local, static and dynamic routes Globally enables multicast routing Shows each multicast route this switch has learned Configures VRRP groups, including virtual interface address, advertisement interval, preemption, priority, and authentication Displays global statistics for VRRP protocol packet errors Uplink ports can communicate with any other ports on the switch and with any designated downlink ports.

When a static address is seen on another interface, the address will be ignored and will not be written to the address table.

Multicast Routing Commands This router uses IGMP snooping and query to determine the ports connected to downstream oen hosts, and to propagate this information back up through the multicast tree to ensure that requested services are forwarded through each intermediate node between the multicast server and its hosts, and also to filter traffic from all of the other interfaces that do not require these services.

This example lists all entries in the multicast table in summary form: If a router is enabled as an ASBR, then every doownload router in the autonomous system can learn about external routes from this device. Command Line Interface Example This example creates a virtual link using the defaults for all optional parameters.

Specify parameters for the LSAs you want to display, then click Query. If ports on another device are also configured as LACP, the switch and doenload other device will negotiate a trunk link between them. Yes, install Microsoft Download Manager recommended No, thanks. Syntax spanning-tree hello-time time no spanning-tree hello-time time – Time in seconds. Example Console config-if ip pim hello-holdtime Console config-if ip pim trigger-hello-interval This command configures the maximum time before transmitting a triggered PIM Hello message after the router is rebooted or PIM is enabled on an interface.

Use the no form to remove an existing key. If the timeout is too short, managfment router may tie up resources by repeating ARP requests for addresses recently flushed from the table. maagement

Example Console show startup-config building startup-config, please wait Example Console config-router probe-interval 30 Console config-router nbr-timeout This command sets the interval manageemnt wait for messages from a DVMRP neighbor before declaring it dead.

Command Line Interface Command Mode Router Configuration Example Console config-router report-interval 90 Console config-router flash-update-interval This command specifies how pne to send trigger updates, which reflect changes in the network topology.

Show Public-key show public-key This command shows the public key for the specified user or for the host.

For security managemfnt, you should consider removing the default strings. It is clearly the best budgeting and money management book on the market today.

This value must be the same for all routers attached to an autonomous system. Use the no form with the multi-host max-count keywords to restore the default maximum count.

You can then attach a protocol analyzer or RMON probe to this port to perform traffic analysis and verify connection integrity. Otherwise, the bind operation will fail.

Free eBook Offer – The One Minute To-Do List – Michael Linenberger

The primary difference is that VRRP requires you to specify the interface of one of the routers participating in the virtual group as the address for the master virtual router, while HSRP requires you to configure an arbitrary address for the virtual master router.

Microsoft recommends you install a download manager. fownload

Console show ip mroute IP Multicast Forwarding is enabled. Default Setting IP address: Change any of the interface-specific protocol parameters, and then click Apply. It is configured to use Weighted Round Robin, which can be viewed with the show queue bandwidth command.

Printable PDF Forms

While Sparse mode is designed for network areas, such as the Wide Area Network, where the probability of multicast clients is low. Houghton Mifflin College Division.

However, you cannot configure both services to use the same UDP port. The VLAN is activated by default.